3D Printing Service
3D Printing Service in Engineering-Grade Materials
Send a STEP or STL file and we will print it in the engineering-grade material that suits the job. Every file is checked before printing, and features that need a precise fit can be machined after.
How It Works
Send your file
STEP preferred, STL works too. Include the quantity and what the part does.
We check it
Wall thickness, orientation, and anything to change for printability or fit.
You get a quote
Based on the material and the machine time.
We print it
In the engineering-grade material that suits the job.
We finish it
Bores, threads and sealing faces machined where they need a precise fit.
We ship it
Anywhere in the US.
Why Engineering-Grade Materials
Everyday printing plastics such as PLA soften at low temperatures and are not made for oils or chemicals. The materials we print are chosen for working parts: depending on the grade, they bring higher heat resistance, stiffness, toughness or chemical resistance. The comparison below shows how they differ.
How the Materials Compare
Indicative values only. These figures are typical values published by filament manufacturers, shown to compare materials in general terms. They are not guaranteed properties of any printed part and should not be used as design values. Real performance depends on the brand, print settings, part geometry and print orientation.
Swipe sideways to see the full table.
| Material (strongest first) | Tensile strength | Stiffness (modulus) | Heat resistance (HDT) | Chemical and moisture resistance | Example uses | Why this material |
|---|---|---|---|---|---|---|
| 1PPA-CFCarbon fiber reinforced polyphthalamide | 168 MPa | 11.8 GPa | 227 °Cat 0.45 MPa load | Good vs oils, fuels, greases and coolants. Absorbs less water than PA6. | Engine-bay brackets, high-load arms, hot jigs and fixtures | Highest strength and stiffness here, and it keeps them when hot. Trade-off: lower impact toughness. |
| 2PA6-CFCarbon fiber reinforced nylon 6 (polyamide 6) | 102 MPa | 4.4 GPa | 164 °Cat 1.8 MPa load | Good vs oils, fuels and most solvents. Absorbs the most water of the group (about 2.4%). | Gears, structural brackets, machine and automation parts | Strong, tough and wear resistant. Best kept out of constantly wet service. |
| 3PA612-CFCarbon fiber reinforced nylon 6/12 (polyamide 612) | 91.9 MPa | 5.1 GPa | 114 °Cat 1.8 MPa load (175 °C at 0.45 MPa) | Good vs oils and fuels. Absorbs about 2.2% water at equilibrium. | Outdoor and sporting gear, archery accessories, functional brackets | Good balance of strength, stiffness and toughness, and more forgiving than PPA-CF. |
| 4PA12-CFCarbon fiber reinforced nylon 12 (polyamide 12) | 77.4 MPa | 3.3 GPa | 105 °C | Very good vs oils, fuels and greases. Lowest water uptake of the nylons (about 1.5%). | Fuel and oil line clips, housings, snap fits | Tough and stable in humid or oily environments. Less stiff than the other nylons. |
| 5PPS-CFCarbon fiber reinforced polyphenylene sulfide | 59.4 MPa | 5.4 GPa | 252 °Cat 0.45 MPa load, annealed | Excellent. Resists most acids, bases and solvents. Almost no water uptake (about 0.2%). Flame retardant (UL94 V-0). | Pump impellers and casings, chemical process parts, hot fluid manifolds | Handles heat and harsh chemicals at the same time. Trade-off: brittle, so not for impact loads. |
| 6PETG-CFCarbon fiber reinforced polyethylene terephthalate glycol | 59 MPa | 2.5 GPa | 68 °C | Fair. Fine with water and many cleaners. Not for solvents or hot service. | Jigs, fixtures, covers, indoor brackets, prototypes | Economical, accurate and clean looking. Good when heat and chemicals are not a concern. |
| 7PPS-GFGlass fiber reinforced polyphenylene sulfide | 57.3 MPa | 4.1 GPa | up to ~220 °Cat 1.8 MPa load, annealed | Excellent, same as PPS-CF. Glass fiber makes it electrically insulating. | Electrical housings and insulators, hot chemical service | PPS chemical and heat resistance where the part must not conduct electricity. |
| 8PP-CFCarbon fiber reinforced polypropylene | 39.8 MPa | 2.6 GPa | ~70 °Cat 0.45 MPa load | Excellent vs acids, bases and many solvents. Almost no water uptake. | Lab fixtures, tank fittings, fluid handling parts | Polypropylene’s chemical resistance with much more stiffness than plain PP. |
| 9PPPolypropylene | ~10 MPa | 0.25 GPa | ~64 °Cat 0.45 MPa load | Excellent vs acids, bases and cleaning chemicals. | Living hinges, containers, chemical-contact parts | Flexible and fatigue resistant. Bends without cracking, but low strength. |
Ranked by tensile strength. All values are indicative only, taken from manufacturer data sheets for dry, printed test bars in the X-Y direction. Strength between layers (Z direction) is lower, and figures vary by brand, print settings and part design. Heat resistance is the heat deflection temperature (HDT): the temperature at which a test bar starts to bend under a set load. A lighter load gives a higher number, so the test load is shown under each value where the data sheet states it. Annealed means the part was heat treated after printing. PP and PP-CF stiffness is flexural modulus. Not sure which material fits your part? Tell us about the load, temperature and chemicals it will see and we will recommend one.
Good Fits for This Service
Jigs and fixtures
Holding, locating and assembly tooling.
Brackets and mounts
Including housings and covers.
Functional prototypes
Test the fit and function before committing.
Small batches
End-use parts with no minimum order.
Fluid handling
Chemical and fluid-contact parts.
Replacement parts
Remade from your file or the old part.
No tooling cost. Design tip: keep walls at least 1.2 mm thick.
Project Evaluation
Have a part or a problem in mind? Send a few photos or drawings and tell us what the part needs to do. The initial evaluation is free, and we’ll give you a straight answer on whether it’s a good fit. We’d rather understand your needs and build a working relationship than just quote a part.
